900R-NPB COLD BOND ADHESIVE

Product Description

Normac 900R NPB is a two component, room temperature curing, chloroprene based, liquid rubber adhesive that, when catalysed with the appropriate amount of Normac R Hardener, yields high strength adhesion when bonding rubber to rubber, rubber to fabric, rubber to steel, rubber to:  concrete, fiberglass, PVC and urethane.


 
Mix Ratio: 900R-NPB
R Hardener
100 8

Package Sizes
Packaged/Sold by Weight

Kit 900R-NPB R Hardener  
0.5kg 0.5L (1 pint) 40g x 1  
1.0kg 1.0L (1 quart) 80g x 1  
5.0kg 4.0L (1 us.gal.) 80g x 5  
25.0kg 18.9L (5 us.gal.) 80g x 25  
290.0kg 200.0L (45 us.gal.) 80g x 290  
Case Sizes
Packaged/Sold by Weight

Case 900R-NPB R Hardener  
0.5kg x 20 0.5kg x 20 40g x 20  
1.0kg x 20 1.0kg x 20 80g x 20  
5.0kg x 4 5.0kg x 4 80g x 20  

Appearance
 
Black, clear amber or FDA compliant white brushable liquid.  

Specific Gravity
Viscosity
1.330 1500 - 3500 cps

Chemical Resistance

Refer to Normac 900R Chemical Resistance Chart.  

Oil Resistance
Operating Temperature
Excellent -40oC to 93oC (-40oF to 200oF)

Application Life
Shelf Life
4 hours @ 21oC (70oF) >2 years in unopened containers

Storage

Store in a dry place at ambient temperatures, away from open flame, sparks and direct sunlight.  

Flammability
Normac 900R is a non-flammable product in shipping, storage and application.

Safety, Handling & Toxicity
See Normac 900R Material Safety Data Sheet (MSDS) for specific information.

Application
Application: For uniform mixing, cement containers should be agitated or drums rotated before the addition of hardener. Thoroughly mix the appropriate amount of hardener (8% by weight) into the cement at 21oC. This mixture will give you an application life of 6-8 hours before cross-linking.

Specific application sheets are available for the following:

1. Bonding rubber sheeting to steel.
2. Bonding urethane sheeting to steel.
3. Bonding urethane sheeting with bonding layer to steel.

Rubber to Steel: Metallic surfaces must be free of oils, grease or other contaminants. Rust and mill-scale should be removed by sand blasting to NACE #2. A profile of 2-3 mils is preferred. The rubber, if cured should have all mould release agents removed and buffed with 24 grit or stiff bristled wire brush at a speed as not to burn the rubber surface. Apply a first coat to each surface with a scrubbing-like motion. Allow this coat to dry for at least 1 hour at 21oC. Should the ambient temperature be lower, allow a 50% increase in drying time for every 3oC drop in temperature. After the required drying time a second coat is applied to each surface in a manner as not to disturb the primary coat. Let dry until tacky, adhere both surfaces and stitch down or apply pressure. The maximum bond strength will develop to its optimum in 21 days, however, initial bond strengths will be sufficiently high after 6 hours and are ready for most services.

Rubber to Rubber: The rubber, if cured in sheet form should be solvent cleaned and buffed as described above before the first coat of adhesive is applied. Allow the first coat to dry for at least 1 hour or longer. Should the temperature be lower, better adhesion will be achieved by increasing the first coat's drying time by 50% for every 3oC drop below ambient. After the required drying time a second coat is applied and when still tacky, stitch the two components together or apply pressure.

Rubber to Other Substrates: For adhering other elastomeric materials or special environmental conditions, please contact our main office. Trials, if possible are recommended before production to determine the suitability of this compound with individual materials and to determine the preferred method of application.

Coverage
Thinner
5m2 per kg. (24.5 ft.2 per lb.) theoretical coverage. Trichloroethylene, NPB(n, Propyl Bromide).

Rev.0
   

900R COLD BOND ADHESIVE

Product Description

Normac 900R is a two component, room temperature curing, chloroprene based, liquid rubber adhesive that, when catalysed with the ap...

Read more...

   

U-SPRAY OVERVIEW

Description: Normac is extremely pleased to introduce a new, revolutionary application process for all of our 100% Solids Sprayable Polyurethane Coating Systems. This application...

Read more...

   

EP-100 ADHESIVE/PRIMER

Product Description

Normac EP100 is a two component, room temperature curing, epoxy based, liquid adhesive.  When catalysed with the appropriate amount...

Read more...

   

SOLVENT BASED COATINGS OVERVIEW

These polyurethane protective coatings, providing corrosion control and abrasion resistance, were developed to be as user friendly as possible. ...

Read more...

   

Product Menu  

   

Language  

   

Login  

   
© Normac Adhesive Products Inc.