Normac NR-55GL Sprayable Urethane

Product Description:  A 100% solids plural component, sprayable urethane polymer system.

Material: MDI polyether and polyol.

Mix Ratio:    Part "A"    Part "B"
Weight:         1     0.9263    

Volume:         1         1

Package Sizes:  Packaged/Sold by Volume

Kit Size:                            Part "A"    Part "B"
2 drums (105 gal. A + B)     55 gal.    55 gals.
                                          500 lbs.    440 lbs.

Application Life: 20-30 sec. @ 21C (70F)

Tack Free: 40-60 seconds @ 21C (70F)

Print Free: 2-4 minutes @ 21C (70F)

Hardness: 55 +/- 5  Shore A

Bashore Resilience:  40% (ASTM D2632)

Impact Resistance:
Greater than 160 inch - pounds (ASTM D2794)

Flexibility:  Pass 1/8" conical mandrel (ASTM D522)

Tear Strength: 23 pli (ASTM D-470),  125 lbs. Die C

Tensile Strength: 800 psi (ASTM D412)

Elongation: 465% (ASTM D412)

Abrasion Resistance:  0.080 grams weight loss per 1000 cycles, H18 wheel, at 1000 gms. (ASTM D1-044)

Operating Temp.:  -56C (-70F) to 93C (200F)

Fungus Resistance:  Non-nutrient

Weight of Cured Coating: 29 gm./m2 @ 25 microns  0.60 lbs. per 100 ft.2 at .001" thick

Modulus 100%:  250 psi (ASTM D412)

Ultimate Cure:  5 days at 30 dry mils at 21C (70F)

Recoat Times: 24 hours without surface preparation

Volatile Organic Compound (V.O.C.): Normac NR-55GL is a 100% solids formulation and as a result has no VOC's.  It is advised to consider local, state, provincial or federal laws pertaining to the application of any coatings prior to use.

Mixed Solids Content: 100% by weight

Flash Point:  None, Normac NR-55GL Part "A" and "B" are both non-flammable in shipping, storage and application.

Application:  Normac NR-55GL is applied through low pressure plural component equipment. The spray gun is both impingement and static mix to suit all types of applications.  This system uses air pressure to purge the tips.  Solvent flushing is not required during application. Typical operating temperatures are approximately 21C (70F).  Air requirements are 100 psi.

Surface Preparation: Bedliners require a light sanding ane no primer is needed. For more details see "Normac Surface Preparation Guide for Urethane Coatings".

Primers:
NR-9500: A two component, single coat air curing solvent based primer.
NR-9600: A two component wash primer base for NR-9500.
900R:  A two component, air curing rubber based primer.
EP-100: A two component 100% solids primer for concrete.
Refer to specific primer/adhesive data sheets.

Theoretical Coverage:   
34 m2 @ 25 microns/kg DFT (366 ft2 @ .001" DFT) or 1 kg. yields 9.16m2 (98.5ft2) at 1mm (.040”/40mils) thickness.

Downloads

Normac NR-55GL Part A MSDS
Normac NR-55GL Part B MSDS

 

   

Product Menu  

   

Language  

   

Login  

   
© Normac Adhesive Products Inc.